Answers
I have this old lawn mower and I am looking to use the engine for a go kart. It is the "Snapper big six" 6HP engine for a walk-behind mower by briggs and stratton. I am looking for a site where I can go to get the basics down about this mower and hopefully read a diagram about all the parts not only of the engine but of the parts of the mower too. Can anyone find a page where I can learn this? Any other tips about making go-karts!? Thank you!
You can get all the information on the engine at outdoordistributors.com. Type in the model number and you will get an exploded view with part numbers.
HOW TO REPAIR the PULSA PRIME Carburetor on Lawnmowers with with Briggs amp; Stratton engines. Visit my channel for more repair videos; www ...
My lawn mower, "Weed Eater 21 B&S 550 series will not work. When i pull the starting cord, it begins to start, but dies as if the gas is not getting through or something. Yes, the lawn mower i have is a gas engine one.
how old is the gas? it could be bad. try draining the tank and putting in some fresh gas.On top of engine there should be big flat head screw. take that out and remove air filter and voila' there is your carb
the NGK spark plug for the Briggs&Stratton will be similar to Rj19lm will this cause any harm?
take the spark plug to your nearest dealer and find out what spark plug options you have, but I think I have seen those in Briggs and Hondas alike. If there is a NGK replacement available, you certainly can use it without causing any harm.
MURRAY 20" 4.0hp Quatro Briggs & Stratton. The mower fluctuates when it is running and i was told to remove the carburator and give it a good cleaning. i do not have the manual for the mower. Thank you.
where is the model number located on the mower? i'm at work right now...
Look here:
http://www.murray.com/products/combined_ search.asp?search=Model&type=OM
You will have to enter the model number in the box. Good luck!
I have a briggs and stratton lawn mower. I've owned for about a year. It has never started easily, and now will not start at all. I am guessing that the carburetor needs to be cleaned. Can anyone provide instructions specifically for briggs and stratton lawn mowers (not sure of the model, bought it last year for about $140) regarding how to remove and clean the carburetor, and what the other causes may be?
Check and see if gas is in the carburetor bowl. If not the check valve is stuck a common problem with gunk build up. When you have it upside down it's under the float. Take the float off and get to it. The check valve is held with small wire parts so take your time and remember how it is held in place. You do have to put it back the same way you found it.
Before I did anything I would check for spark. Then I would pull the plug out and put two teaspoons of gas in the engine. Put the plug back and it will start and run most of the time. Only do that on a cold engine for your safety.
1974 Jari Monarch Walk Behind, Self-Propelled Sickle Bar Mower ...
Made in Mankato, Minnesota. JARI’s (Jacob A. Ronning, Inc.) initial era (spanning 40+ Years) tip of the line, blurb peculiarity “Monarch” Sickle Bar Mower featuring the twin circle pattern choice along with serrated slicing edges which is generally beneficial when slicing in an area with saplings. This appurtenance is driven wholly by belts as well as pully’s off of the Briggs 5HP engine. “Transmission” speed cannot be practiced seperately from the knife edge speed, which is a good of the brand new …
Briggs and Stratton help
Welcome
to Tech Support Forum home to more then 136,000 problems solved. Issues
have included: Spyware, Malware, Virus Issues, Windows, Microsoft,
Linux, Networking, Security, Hardware, and Gaming Getting your
problem solved is as easy as:
1. Registering for
a free account
2. Asking your
question
3. Receiving an answer
Registered members:
* Get free support
* Communicate privately with other members (PM).
hello my mower( rover lawn mower with a briggs and stratton quantum XM 50 engine,Model number (12F802) Engine Type (1975-B1) ) will not start ive have tried almost everything i can think of, first i flushed the fuel tank and put new fuel in still didnt start then i cleaned the coil for surface rust and set the gap again and cleaned the flywheel/magneto from surface rust still didnt start then i cleaned out carby and bowl and bowl screw with carby cleaner and cmpressed air in all the holes still didn start then i took out the valves and cleaned all the seats and the valves and the top of the piston and any other excesse carbon there was a lot of carbon still didnt start then i put new spark plug and air filters in still didnt start i also tried starter fluid and still didnt not start. lol the only thing i can think of now is piston ring? i cant think of anything else . can anyone help me !! ???? lol