Answers
I must have bumped the mower into something..and the lever toggles while riding mower. It doesn't stop blade, but I want to correct this.
Thanks.
Check all your bolts and nuts for loose connections,and quit running over stuff.(Advise to me from my old man,after it cost $$$$$$$ to find out all I had wrong was a really loose bolt) Good luck!
How to sharpen a lawn mower blade, step by step.
I've looked at the blades and the belt, they seem to look and turn fine. It starts fine and runs fine until I engage the blade.
It's a murray.
It dies completely.
No it is not stuck in reverse, like I said it will drive fine as long as the blades aren't down.
I know I'm a girl but you can give me more credit than that.
Are you seated when you engaged the blade? I agree it sounds like a safety switch somewhere.
drive belt?
Sure, it needs to be tight to properly cut. Look under the deck or feel up under there. Usually there is a single bolt holding each blade in the center, 1/2 inch or maybe bigger. Tighten it with a socket wrench. Some older snapper mowers had no center bolt, but had two 3/4 inch bolts about eight inches from the center. Good luck.
On a riding mower you will need to safely lift and support the rider somehow so that it can't slip or fall. I have a rope lift I use in the garage but a sturdy tree limb would also work fine. You might be able to elevate one side so that it tilts right or left but do not trust a hydraulic jack to hold it up. Use a tool or a block of wood to prevent the blade from turning. There is a large nut or bolt you must loosen on each blade. Turn it the opposite direction the hands on a clock turn. There should also be a lock washer that prevents the nut from loosening. Save and reuse it. Pay carefull attention to any flat washers that are also fastened with the blade. My older mower has two washers above the blade and one below. Those affect the height of the cut and in some cases must be in that position in order to hold the blade in place.
If you don't have a grinder you can sharpen the blade with a file. It might take awhile but it will work. You can use any bolt or plastic pen as a balance tester. Place the bolt through the hole on the blade and hold it straight out in front of you as if you were pointing the bolt at something in front of you. See if the blade remains fairly level. If one side dips down, it is heavy. Remove some more metal from the low side and retest the balance until it sits fairly level.
While you have the blade off, it would be a good time to clean out the mower deck. Look for grass deposits, wire, string ....anything that will catch grass and slow down the grass from being spun out of the mower.
Replace the blade with the original washers and tighten the nut or bolt using something to prevent the blade from turning. Turn the wrench the same way as the hands on a clock to tighten.
Remember, when it comes to nuts and bolts,
right is tight,
left is loose...
I have a Craftsman TS1000 riding lawn mower and my son ran over a large rock that damaged one of the two blades. After replacing the damaged blade, the lawn mower cuts unevenly. I put the lawn mower on a level surface and can see that the mower deck is uneven, but I don't know how to adjust it. Can you help me?
There are adjusters on each side of the deck. Put the mower on a level surface and you can screw/unscrew them to level the deck. Also, make sure the air pressure in the tires are correct. That's one of those overlooked problems that can cause an uneven cut.
Riding Lawn Mower Blade Care
Occasionally, a lawn tractor or riding mower blades may be unbalanced, bent, or dull and will need reconditioning or replacement. It is recommended that the maintenance performed on the blades at least twice a year. Looking for blades of a riding lawnmower, follow the steps listed below.
NOTE: These materials are prepared for use by technicians trained and experienced service and repair of equipment of the kind described in this publication, and are notintended to be used by individuals untrained or inexperienced. These people should seek the assistance of a service technician or your dealer.
Preparation
Like many projects, think safety. Always wear heavy leather gloves and safety glasses for protection and always disconnect both the mass of wire from the battery negative terminal of the battery and spark plug ignition of the candle. If the device is equipped with an engine cylinder, remove the twoson of the spark plug of the spark plug.
...Seven Common Riding Lawn Mower Problems and Solutions
Lawn mowers are incredibly valuable and useful tools that can save time and energy spent on yard work. However, lawn mowers can have problems and need maintenance. Listed below are seven (7) common problems riding mower lawn with troubleshooting tips. If a problem can not be solved by the advice contained in this article, contact a repair shop.
NOTE: These materials are prepared for use by technicians trained and experienced service and repairequipment of the kind described in this publication, and are not intended to be used by individuals untrained or inexperienced. These people should seek the assistance of a service technician or your dealer.
Problem 1: The engine does Crank
News
Spring Lawn CareFOX Charlotte - Mar 04, 2010
Your lawnmower needs an oil change, along with a filter and tire check. The sharpness of your mower blade and mower height are especially important.Milwaukee Journal Sentinel - Feb 27, 2010
In basic terms, torque is a measurement of the force needed to turn something such as a lawn mower blade. It#39;s a better measurement of a mower#39;s ability to and morenbsp;raquo;Associated Content - Feb 17, 2010
Lawn mowers have different features to perform different types of grass cutting. This equipment uses blades to cut the grass. Different grass types do wellBigNews.biz (press release) - Feb 23, 2010
The Yard Machines 139cc MTD OHV engine is applied to gently push the mower across the lawn. It carries a 22-Inch cutting blade, side discharge with 7-InchGreater Greater Washington - Feb 21, 2010
But in the meantime, I think SJE has a point -- outfitting garden tractors/riding lawn mowers with snow blades and plowing the sidewalks amp; trails wouldWooster Daily Record - Feb 17, 2010
quot;I have the time to do it, and my tractor blade is just wide enough for the sidewalk. It#39;s not a problem,quot; he said. Unfortunately, this past weekend#39;sSussex Countian - Feb 11, 2010
The six-wheeled behemoth of a dump truck is filled to the brim with a mixture of sand and road salt and fitted with a massive steel plow blade as wide as a and morenbsp;raquo;
